Tropitone's cast aluminum patio furniture collections represent the finest in handcrafted, heirloom quality, casual aluminum outdoor furniture. From the original woodcarvings, to the hand-poured molten aluminum, to the meticulous grinding and polishing, the pride of craftsmanship is evident in every joint and detail. Tropitone also uses a harder alloy for our cast aluminum patio furniture than is commonly found in outdoor furniture, offering unmatched detail and superior finishing. Our all-aluminum patio furniture frames are hand-welded and finished with a durable powder coating - which Tropitone was the first to use for aluminum outdoor furniture.

FINISHES
Cleaning and Protecting
For all textured finishes on cast aluminum outdoor furniture, a mild soap and warm water wash is recommended.

Repairing Scratches and Scrapes in Finish:
Touch-up paint to match the frame color of your cast aluminum patio furniture is available directly from your Tropitone Dealer. Before beginning any touch-up procedure, always wash the marred area first to remove any dirt or grease, then lightly sand the edges around the scratch so that the touch-up paint will blend in easily.

Spray Cans for Touching Up Textured Finishes
Hold spray can 8 - 10 inches away from surface of aluminum outdoor patio furniture to be touched up. Do not try to get full coverage with the first coat. Spray a thin coat and let dry. Spray a second coat and let dry. Continue applying until desired coverage is achieved. Trying to get full coverage in the first coat may result in a glossy surface. Should this happen, dull with a light (thin) "dusting" coat applied after the offending glossy coat has dried.

Small Nicks - Spray touch-up paint onto a flat plate or dish. Then use a small artist's brush to transfer the paint from the plate to the aluminum outdoor patio furniture. Texture can be enhanced with a clean, dry brush after the paint becomes tacky.

Scratches - Spray touch-up paint directly onto the outdoor patio furniture, heavily enough to cover the blemish. Wait 3 - 5 minutes for the paint to become tacky. Note: A dry cloth will pick up too much paint. Make sure your cloth is lint free.

For Scrapes Down to Bare Metal - Spray touch-up paint directly onto cast aluminum outdoor furniture heavily enough to cover the blemish. Then, sprinkle fine grain silicone sand on the wet paint. Re-coat with a light spray after the first coat dries.

When applying touch-up paint, it's better to use many light coasts rather than just one heavy coat as the solvents in the spray paint may cause the surrounding finish to loosen and wrinkle.

Storage hint - Always store touch-up spray cans "upside down" as the nozzles are less likely to clog this way.

Touching up Cast "Weathered" and "Antiqued" Cast Aluminum Patio Furniture Finishes -
First, follow the above procedure and allow the undercoat to dry. Then, using a cotton swab, lightly apply the supplied glaze color from your touch-up-kit. Blend-in with a soft cloth and allow to dry. If possible, experiment first on a hidden area of the frame.

FRAMES
For Cast Aluminum Outdoor Furniture Products - All dining tables have a leveling glide on one leg, which can be adjusted so the table will sit level. For all seating pieces and side tables: If there is serious unevenness that cannot be corrected by switching the chair with another chair on the floor, contact your Tropitone Dealer about obtaining a replacement.

FABRICS
General Information - Note: Do not use bleach unless specifically listed as a cleaning agent for your specific fabric. The life of your patio furniture fabric largely depends on its care and use. Certain suntan and sun block products may permanently discolor any fabric. This possibility can be minimized by immediately cleaning after contact. It is important to clean your fabric regularly. In addition, storing your cushions when not is use, or using furniture covers will extend their life. Also, fabric life can be extended by simply hosing down your patio furniture regularly with water. Hint: Cushions dry faster if they are allowed to stand on their sides while drying.

 100 Series - Vinyl for Cast Seats.
Spot wash with a lukewarm (no warmer than 100 degrees) solution of mild liquid soap and water. Rub briskly with a rough cloth or soft bristle brush. Rinse thoroughly with clean water to remove soap. Allow to air dry. Do not use bleach, harsh detergents or stiff bristle brushes on the 100 Series vinyl materials.

 1000, 2000 Series - Vinyl Coated Polyester Weaves
Soil, Suntan Oil and Lotions: Promptly remove with solution of 1 cup of liquid detergent-water solution.
Oils and grease: Spot treat with bleach and rubbing alcohol.
Mildew: Treat with warm water, detergent and bleach mixture indicated above.
Berry Juices, Wine and Blood: Use strong liquid detergent, warm water and ammonia.
Always rinse thoroughly after applying any cleaning product.

 3000 Series - 100% Polyester Prints & 8000 Series - 100% Acrylic/Olefin Blends
Promptly remove soil (including suntan oils and lotions) with a solution consisting of two capfuls of mild liquid soap per gallon of water. Be liberal with solution and scrub with a soft brush. Rinse thoroughly with clean water to remove soap and air dry. DO NOT USE BLEACH OR HARSH DETERGENTS ON ANY PRINTED FABRIC.
Note: These fabrics are not recommended for poolside applications.

 3500 Series - Polyester/Olefin Blends and Acrylic/Olefin Blends
Clean spills as soon as possible. If a spot remains, use a mild detergent to water solution. Occasionally, add 1 cup of household bleach to the detergent-water solution. Rinse entire cushion or umbrella with water. Air dry.
Baby Oil, Beer, Orange Juice and Coffee: Apply hot water and detergent. Rinse the entire piece thoroughly. If necessary, apply a laundry pre-wash, leave on for 10 minute's, and then reapply hot water and detergent. Rinse thoroughly.
Blood Stains: Apply protein or enzyme spotter.
Oil and Suntan Lotion: Apply a volatile-type paint remover or 100% mineral spirits to stain.
Ink, Marker or Mascara: Apply Grain or Wood Alcohol to stain.

 4000, 6000, 7000 and 9000 Series
Acrylic/Polyester Blends and 100% Acrylic Fabrics.
Spot wash with a lukewarm (no warmer than 100 degrees) solution of mild liquid soap and water. Rub briskly with a rough cloth or soft bristle brush. Rinse thoroughly with clean water to remove soap. Allow to air dry. Do not use bleach, harsh detergents or stiff bristle bushes on acrylic blend fabrics.
For stubborn stains and suntan lotions, we recommend "Spic & Span" or a fine fabric cleaner. Use full strength and apply vigorously with a sponge or clean cloth. Sponge thoroughly with clean water. Allow to air dry.
Note: 100% acrylic fabric is heat sensitive. Do not use heat, hot water or bleach.

 5000 Series - Acrylic/PVC Blends
Spot wash by sponging briskly with a lukewarm solution of mild liquid soap and water. Sponge thoroughly to remove soap and then air dry. For suntan lotion, use fine fabric cleaner. Do not use Pine Oil cleaners or abrasive household cleaners.